Samsung Galaxy S6 edge G925FXXU3DPCF
SM-G925F 1 country Android 6.0.1 (Nougat)

Samsung Galaxy S6 edge G925FXXU3DPCF Firmware

Samsung Galaxy S6 edge G925FXXU3DPCF is an Android 6.0.1 (Nougat) firmware for France (FTM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G925FXXU3DPCA: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1 (Nougat). A newer build for SM-G925F is available: G925FXXU6EVI1.

Download firmware
8.7/10 (459)4,384 times
Android 6.0.1 (Nougat)
OS Version
2016-03-16
Build Date
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 edge use bootloader binary 6 (latest: G925FXXU6EVI1). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G925FXXU3DPCF
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G925F
    FTM France
    		G925F3DPBT — — Download

    No matching downloads

    How to flash G925FXXU3DPCF

    • G925FXXU3DPCF has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.1 GHz
    • Processor familySamsung Exynos
    • Processor model7 Octa 7420
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight132 g

    Frequently Asked Questions

    G925FXXU3DPCF is Android 6.0.1 (Nougat) firmware for Samsung Galaxy S6 edge, released for France (FTM). Samsung built it on 2016-03-16.

    No. A newer build for SM-G925F is available: G925FXXU6EVI1. Install it instead of G925FXXU3DPCF unless you need this exact version. The previous build was G925FXXU3DPCA.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 edge must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 edge running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 99 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 edge

    No changelog details available.

    • GPS
    The stability has been improved.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • GPS
    The stability has been improved.

    Show 8 older builds
    No changelog details available.

    • The security of your device has been improved.

    No changelog details available.

    • The security of your device has been improved.

    Model firmware by region