SM-G925I 1 country Android 7.0 (Nougat)

Samsung Galaxy S6 Edge G925IDVS3FQEC Firmware

Name: Samsung Galaxy S6 Edge (SM-G925I)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 Edge G925IDVS3FQEC is an Android 7.0 (Nougat) firmware for India (INS, INU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G925IDVS3FQEB, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G925I is available: G925IDVU4FVHR.

9.1/10 (452)8,609 times

Android 7.0 (Nougat)

OS Version

2017-05-25

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 Edge use bootloader binary 4 (latest: G925IDVU4FVHR). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G925IDVS3FQEC

Model	Region	CSC Version	Size	File name	Download
SM-G925I	INS India	G925IODD3FQE1	—	—
SM-G925I	INU India	G925IODD3FQE1	—	—

Device specifications

Launched withAndroid 5.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity2600 mAh
Weight132 g

Specifications of SM-G925F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G925IDVS3FQEC

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G925IDVS3FQEC has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G925IDVS3FQEC is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge, released for India (INS, INU). Samsung built it on 2017-05-25.

No. A newer build for SM-G925I is available: G925IDVU4FVHR. Install it instead of G925IDVS3FQEC unless you need this exact version. The previous build was G925IDVS3FQEB.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 152 other builds of this model use the same binary, so you can switch between them in both directions.