Samsung Galaxy S6 Edge G925IDVS3FQH2 Firmware
Samsung Galaxy S6 Edge G925IDVS3FQH2 is an Android 7.0 (Lollipop) firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G925IDVU3FQG2: Android updated from Android 7.0 (Nougat) to Android 7.0 (Lollipop). A newer build for SM-G925I is available: G925IDVU4FVHR.
9.4/10 (452)21,940 times
Android 7.0 (Lollipop)
OS Version
2017-08-09
Build Date
n/a
Security patch
4
Countries
5
CSC codes
3
Bootloader binary
Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy S6 Edge use bootloader binary 4 (latest: G925IDVU4FVHR). If your device already runs binary 4, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
MODEM/CP Version: G925IDVS3FQH2
Device specifications
- Launched withAndroid 5.0
- Display diagonal12.9 cm (5.1")
- Display resolution2560 x 1440 pixels
- Display typeSAMOLED
- RAM3 GB
- Rear camera resolution16 MP
- Rear camera typeSingle camera
- Battery capacity2600 mAh
- Weight132 g
Specifications of SM-G925F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.
How to flash G925IDVS3FQH2
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- G925IDVS3FQH2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
G925IDVS3FQH2 is Android 7.0 (Lollipop) firmware for Samsung Galaxy S6 Edge, released for 4 countries, 5 CSC codes. Samsung built it on 2017-08-09.
No. A newer build for SM-G925I is available: G925IDVU4FVHR. Install it instead of G925IDVS3FQH2 unless you need this exact version. The previous build was G925IDVU3FQG2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge must be on bootloader binary 3 or lower.
This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 152 other builds of this model use the same binary, so you can switch between them in both directions.