Samsung Galaxy S6 Edge G925KKKU3DPAD
SM-G925K 1 country Android 6.0.1 (Lollipop)

Samsung Galaxy S6 Edge G925KKKU3DPAD Firmware

Samsung Galaxy S6 Edge G925KKKU3DPAD is an Android 6.0.1 (Lollipop) firmware for South Korea (KTC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G925KKKU3COK2: Android updated from Android 5.1.1 (Lollipop) to Android 6.0.1 (Lollipop). A newer build for SM-G925K is available: G925KKKU3EVG1.

8.9/10 (455)8,625 times
Android 6.0.1 (Lollipop)
OS Version
2016-01-25
Build Date
n/a
Security patch
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G925KKKU3DPAD
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G925K
    KTC South Korea
    		G925K3DPAD — —
    SM-G925K
    KTC South Korea
    		G925KRTC3DPAD — —

    No matching downloads

    How to flash G925KKKU3DPAD

    • G925KKKU3DPAD has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight132 g

    Specifications of SM-G925F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G925KKKU3DPAD is Android 6.0.1 (Lollipop) firmware for Samsung Galaxy S6 Edge, released for South Korea (KTC). Samsung built it on 2016-01-25.

    No. A newer build for SM-G925K is available: G925KKKU3EVG1. Install it instead of G925KKKU3DPAD unless you need this exact version. The previous build was G925KKKU3COK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge

    No changelog details available.
    Model firmware by region