Samsung Galaxy S6 Edge G925PVPU4DQC7
SM-G925P 1 country Android 7.0 (Lollipop)

Samsung Galaxy S6 Edge G925PVPU4DQC7 Firmware

Samsung Galaxy S6 Edge G925PVPU4DQC7 is an Android 7.0 (Lollipop) firmware for United States (BST, SPR, VMU, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G925PVPS4CQB1: Android updated from Android 6.0.1 (Marshmallow) to Android 7.0 (Lollipop). A newer build for SM-G925P is available: G925PVPS4DRC2.

Download firmware
9.2/10 (456)17,179 times
Android 7.0 (Lollipop)
OS Version
2017-03-24
Build Date
1
Countries
4
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G925PVPU4DQC7
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G925P
    BST, SPR, VMU, XAS United States
    		G925PSPT4DQC7 2017-04-26 2.25 GiB
    SM-G925P_1_20180425113227_mcs29cm3x5_fac.zip

    No matching downloads

    How to flash G925PVPU4DQC7

    • G925PVPU4DQC7 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G925PVPU4DQC7 by region

    Samsung released this build in all regions (4) on the same day, April 26, 2017.

    Device specifications

    • Launched withAndroid 5.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight132 g

    Specifications of SM-G925F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G925PVPU4DQC7 is Android 7.0 (Lollipop) firmware for Samsung Galaxy S6 Edge, released for United States (BST, SPR, VMU, XAS). Samsung built it on 2017-03-24.

    No. A newer build for SM-G925P is available: G925PVPS4DRC2. Install it instead of G925PVPU4DQC7 unless you need this exact version. The previous build was G925PVPS4CQB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.25 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Edge must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy S6 Edge running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 14 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge

    No changelog details available.
    Model firmware by region