SM-G928G 2 countries Android 7.0 (Marshmallow)

Samsung Galaxy S6 Edge+ G928GDDS3CQL4 Firmware

Name: Samsung Galaxy S6 Edge+ (SM-G928G)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 Edge+ G928GDDS3CQL4 is an Android 7.0 (Marshmallow) firmware for India (INS), Sri Lanka (SLK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928GDDS3CQK1 https://samfirm.shop/build/G928GDDS3CQK1: Android updated from Android 7.0 (Lollipop) to Android 7.0 (Marshmallow). A newer build for SM-G928G is available: G928GUBU5CVGH https://samfirm.shop/build/G928GUBU5CVGH.

9.1/10 (453)8,636 times

Android 7.0 (Marshmallow)

OS Version

2017-12-11

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 Edge+ use bootloader binary 5 (latest: G928GUBU5CVGH). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: G928GDDS3CQL4

Model	Region	CSC Version	Size	File name	Download
SM-G928G	INS India	G928GODD3CQJ2	—	—
SM-G928G	SLK Sri Lanka	G928GODD3CQJ2	—	—

Device specifications

Launched withAndroid 5.1
Display diagonal14.5 cm (5.7")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM4 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight153 g

Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G928GDDS3CQL4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G928GDDS3CQL4 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G928GDDS3CQL4 is Android 7.0 (Marshmallow) firmware for Samsung Galaxy S6 Edge+, released for India (INS), Sri Lanka (SLK). Samsung built it on 2017-12-11.

No. A newer build for SM-G928G is available: G928GUBU5CVGH. Install it instead of G928GDDS3CQL4 unless you need this exact version. The previous build was G928GDDS3CQK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge+ must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 60 other builds of this model use the same binary, so you can switch between them in both directions.