Samsung Galaxy S6 Edge+ G928GUBU5CVG6
SM-G928G 3 countries Android 7.0 (Nougat)

Samsung Galaxy S6 Edge+ G928GUBU5CVG6 Firmware

Samsung Galaxy S6 Edge+ G928GUBU5CVG6 is an Android 7.0 (Nougat) firmware for Chile (CHO), Colombia (COM), Dominican Republic (CDR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928GUBU5CVG5, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G928G is available: G928GUBU5CVGH.

Download firmware
8.9/10 (469)13,249 times
Android 7.0 (Nougat)
OS Version
2022-08-23
First release
other regions until 2022-09-07
2018-08-01
Security patch
3
Countries
3
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G928GUBS5CRH4
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-G928G
    CDR Dominican Republic
    		G928GCDR5CTJ1 2022-08-23 2022-08-23 2.408 GiB
    SM-G928G_1_20220823110050_1ognwsas77_fac.zip
    		Download
    SM-G928G
    CHO Chile
    		G928GUUB5CTJ3 2022-09-07 2022-09-07 2.248 GiB
    SM-G928G_1_20220906160150_yu0clx4eau_fac.zip
    		Download
    SM-G928G
    COM Colombia
    		G928GCOM5CTJ1 2022-09-07 2022-09-07 2.385 GiB
    SM-G928G_1_20220906160311_uqnkmaklm6_fac.zip
    		Download

    No matching downloads

    How to flash G928GUBU5CVG6

    • G928GUBU5CVG6 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in G928GUBU5CVG6

    • GPS
    The stability has been improved.

    Rollout of G928GUBU5CVG6 by region

    First release
    August 23, 2022
    Last region
    September 7, 2022
    Duration
    16 days
    Regions
    3
    1. Day 1 · · 1 region
      Dominican RepublicCDR
    2. Day 16 · · 2 regions
      ChileCHOColombiaCOM

    Device specifications

    • Launched withAndroid 5.1
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight153 g

    Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G928GUBU5CVG6 is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge+, released for Chile (CHO), Colombia (COM), Dominican Republic (CDR). It includes the 2018-08-01 security patch. Samsung built it on 2022-08-23.

    No. A newer build for SM-G928G is available: G928GUBU5CVGH. Install it instead of G928GUBU5CVG6 unless you need this exact version. The previous build was G928GUBU5CVG5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge+ must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 47 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge+

    • GPS
    The stability has been improved.

    · Security patch update
    Model firmware by region