Samsung Galaxy S6 Edge+ G928GUBU2BPD2
SM-G928G 5 countries Android 6.0.1 (Lollipop)

Samsung Galaxy S6 Edge+ G928GUBU2BPD2 Firmware

Samsung Galaxy S6 Edge+ G928GUBU2BPD2 is an Android 6.0.1 (Lollipop) firmware for 5 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928GUBS2BPD1: Android updated from Android 6.0.1 (Nougat) to Android 6.0.1 (Lollipop). A newer build for SM-G928G is available: G928GUBU5CVGH.

8.9/10 (455)25,917 times
Android 6.0.1 (Lollipop)
OS Version
2016-04-07
First release
other regions until 2016-07-22
n/a
Security patch
5
Countries
5
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 Edge+ use bootloader binary 5 (latest: G928GUBU5CVGH). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G928GUBU2BPD2
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-G928G
    BVO Bolivia
    		G928GUUB2BPD2 2016-04-07 2016-04-18 2.258 GiB
    SM-G928G_1_20220913175921_1hy2repgtu_fac.zip
    SM-G928G
    CHE Chile
    		G928G2BPD2 2016-04-07 — — —
    SM-G928G
    PSN Argentina
    		G928G2BPD2 2016-04-07 — — —
    SM-G928G
    PSN Argentina
    		G928GPSN2BPD2 2016-04-07 2016-06-09 2.258 GiB
    SM-G928G_1_20220930130040_po2n9uwrjk_fac.zip
    SM-G928G
    UFU Uruguay
    		G928GTFG2BPD2 2016-07-22 2016-07-22 1.915 GiB
    SM-G928G_1_20160722091254_ff6mgpxg76_fac.zip
    SM-G928G
    ZTA Brazil
    		G928G2BPD2 2016-04-07 — — —

    No matching downloads

    How to flash G928GUBU2BPD2

    • G928GUBU2BPD2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G928GUBU2BPD2 by region

    First release
    April 18, 2016
    Last region
    July 22, 2016
    Duration
    96 days
    Regions
    3
    1. Day 1 · · 1 region
      BoliviaBVO
    2. Day 53 · · 1 region
      ArgentinaPSN
    3. Day 96 · · 1 region
      UruguayUFU

    Device specifications

    • Launched withAndroid 5.1
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight153 g

    Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G928GUBU2BPD2 is Android 6.0.1 (Lollipop) firmware for Samsung Galaxy S6 Edge+, released for 5 countries, 5 CSC codes. Samsung built it on 2016-04-07.

    No. A newer build for SM-G928G is available: G928GUBU5CVGH. Install it instead of G928GUBU2BPD2 unless you need this exact version. The previous build was G928GUBS2BPD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge+ must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 23 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge+

    • GPS
    The stability has been improved.

    · Security patch update
    Model firmware by region