Samsung Galaxy S6 Edge+ G928TUVU4DPK6
SM-G928T 1 country Android 6.0.1 (Lollipop)

Samsung Galaxy S6 Edge+ G928TUVU4DPK6 Firmware

Samsung Galaxy S6 Edge+ G928TUVU4DPK6 is an Android 6.0.1 (Lollipop) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928TUVS4DPH2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G928T is available: G928TUVU6EVG2.

Download firmware
9.1/10 (459)8,924 times
Android 6.0.1 (Lollipop)
OS Version
2016-11-25
Build Date
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 Edge+ use bootloader binary 6 (latest: G928TUVU6EVG2). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G928TUVU4DPK6
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G928T
    TMB United States
    		G928T4DPK6 — — — Download
    SM-G928T
    TMB United States
    		G928TTMB4DPK6 2016-12-06 2.244 GiB
    SM-G928T_1_20220819165330_5f4k8gw950_fac.zip
    		Download

    No matching downloads

    How to flash G928TUVU4DPK6

    • G928TUVU4DPK6 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.1
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight153 g

    Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G928TUVU4DPK6 is Android 6.0.1 (Lollipop) firmware for Samsung Galaxy S6 Edge+, released for United States (TMB). Samsung built it on 2016-11-25.

    No. A newer build for SM-G928T is available: G928TUVU6EVG2. Install it instead of G928TUVU4DPK6 unless you need this exact version. The previous build was G928TUVS4DPH2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.244 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Edge+ must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge+

    • GPS
    The stability has been improved.

    No changelog details available.
    Model firmware by region