Samsung Galaxy S7 G930FXXS3ERKA
SM-G930F 12 countries Android 8.0.0 (Oreo)

Samsung Galaxy S7 G930FXXS3ERKA Firmware

Samsung Galaxy S7 G930FXXS3ERKA is an Android 8.0.0 (Oreo) firmware for 12 countries, 20 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930FXXU3ERK6, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G930F is available: G930FXXU8EZCD.

Download firmware
8.7/10 (457)86,522 times
Android 8.0.0 (Oreo)
OS Version
2018-11-08
Build Date
12
Countries
20
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 8 (latest: G930FXXU8EZCD). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    20
    MODEM/CP Version: G930FXXS3ERKA
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G930F
    ANC Argentina
    		G930F3ERKB — —
    SM-G930F
    ARO Argentina
    		G930FUUB3ERKA — —
    SM-G930F
    BAT Mexico
    		G930FUWE3ERKA — —
    SM-G930F
    BVO Bolivia
    		G930FUUB3ERKA — —
    SM-G930F
    CHE Chile
    		G930F3ERKC — —
    SM-G930F
    CHL Chile
    		G930F3ERKA — —
    SM-G930F
    COO Colombia
    		G930FUUB3ERKA — —
    SM-G930F
    CWW Jamaica
    		G930FUWE3ERKA — —
    SM-G930F
    EON Trinidad & Tobago
    		G930FUUB3ERKA — —
    SM-G930F
    ICE Costa Rica
    		G930F3ERKC — —
    SM-G930F
    JDI Jamaica
    		G930F3ERKC — —
    SM-G930F
    PEO Peru
    		G930FUUB3ERKA — —
    SM-G930F
    PSN Argentina
    		G930F3ERKA — —
    SM-G930F
    PVT Peru
    		G930F3ERKA — —
    SM-G930F
    TPA Panama
    		G930FUUB3ERKB — —
    SM-G930F
    TTT Trinidad & Tobago
    		G930FUUB3ERKA — —
    SM-G930F
    UPO Uruguay
    		G930FUUB3ERKA — —
    SM-G930F
    UYO Uruguay
    		G930FUUB3ERKA — —
    SM-G930F
    ZTO Brazil
    		G930F3ERKA — —
    SM-G930F
    ZTR Brazil
    		G930F3ERKB — —

    No matching downloads

    How to flash G930FXXS3ERKA

    • G930FXXS3ERKA has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • Processor familySamsung Exynos
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3000 mAh
    • Weight152 g

    Frequently Asked Questions

    G930FXXS3ERKA is Android 8.0.0 (Oreo) firmware for Samsung Galaxy S7, released for 12 countries, 20 CSC codes. Samsung built it on 2018-11-08.

    No. A newer build for SM-G930F is available: G930FXXU8EZCD. Install it instead of G930FXXS3ERKA unless you need this exact version. The previous build was G930FXXU3ERK6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S7 must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S7 running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 37 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.

    • GPS
    The stability has been improved.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region