Samsung Galaxy S7 G930FXXS6ESGE
SM-G930F 1 country Android 8.0.0 (Oreo)

Samsung Galaxy S7 G930FXXS6ESGE Firmware

Samsung Galaxy S7 G930FXXS6ESGE is an Android 8.0.0 (Oreo) firmware for Australia (OPS, TEL, VAU, XSA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930FXXS6ESGD, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G930F is available: G930FXXU8EZCD.

Download firmware
8.9/10 (41)17,542 times
Android 8.0.0 (Oreo)
OS Version
2019-07-30
First release
other regions until 2019-08-08
1
Countries
4
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 8 (latest: G930FXXU8EZCD). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930FXXS6ESGE
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-G930F
    OPS Australia
    		G930F6ESGE 2019-07-30 — — — Download
    SM-G930F
    TEL Australia
    		G930FTEL6ESGE 2019-08-08 2019-09-02 2.376 GiB
    SM-G930F_1_20190808103014_ifj84lonps_fac.zip
    		Download
    SM-G930F
    TEL Australia
    		G930F6ESGE 2019-07-30 — — — Download
    SM-G930F
    VAU Australia
    		G930F6ESGE 2019-07-30 — — — Download
    SM-G930F
    XSA Australia
    		G930FXSA6ESGE 2019-08-08 2019-09-04 2.248 GiB
    SM-G930F_1_20190808102440_ff1y6xon2b_fac.zip
    		Download
    SM-G930F
    XSA Australia
    		G930F6ESGE 2019-07-30 — — — Download

    No matching downloads

    How to flash G930FXXS6ESGE

    • G930FXXS6ESGE has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G930FXXS6ESGE by region

    First release
    September 2, 2019
    Last region
    September 4, 2019
    Duration
    3 days
    Regions
    2
    1. Day 1 · · 1 region
      AustraliaTEL
    2. Day 3 · · 1 region
      AustraliaXSA

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • Processor familySamsung Exynos
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3000 mAh
    • Weight152 g

    Frequently Asked Questions

    G930FXXS6ESGE is Android 8.0.0 (Oreo) firmware for Samsung Galaxy S7, released for Australia (OPS, TEL, VAU, XSA). Samsung built it on 2019-07-30.

    No. A newer build for SM-G930F is available: G930FXXU8EZCD. Install it instead of G930FXXS6ESGE unless you need this exact version. The previous build was G930FXXS6ESGD.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S7 must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy S7 running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 23 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.

    • GPS
    The stability has been improved.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region