Samsung Galaxy S7 G930FXXS6ESJC
SM-G930F 1 country Android 8.0.0 (Oreo)

Samsung Galaxy S7 G930FXXS6ESJC Firmware

Samsung Galaxy S7 G930FXXS6ESJC is an Android 8.0.0 (Oreo) firmware for Peru (SAM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930FXXS6ESJB, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G930F is available: G930FXXU8EZCD.

Download firmware
9.4/10 (473)4,461 times
Android 8.0.0 (Oreo)
OS Version
2019-10-14
Build Date
n/a
Security patch
1
Countries
1
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 8 (latest: G930FXXU8EZCD). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930FXXS6ESIA
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G930F
    SAM Peru
    		G930FUWT6ESJA 2019-10-23 2.639 GiB
    SM-G930F_1_20201122004834_d9w3lioc5k_fac.zip

    No matching downloads

    How to flash G930FXXS6ESJC

    • G930FXXS6ESJC has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • Processor familySamsung Exynos
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3000 mAh
    • Weight152 g

    Frequently Asked Questions

    G930FXXS6ESJC is Android 8.0.0 (Oreo) firmware for Samsung Galaxy S7, released for Peru (SAM). Samsung built it on 2019-10-14.

    No. A newer build for SM-G930F is available: G930FXXU8EZCD. Install it instead of G930FXXS6ESJC unless you need this exact version. The previous build was G930FXXS6ESJB.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.639 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy S7 running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 23 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.

    • GPS
    The stability has been improved.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region