Samsung Galaxy S7 G930R6WWS8CRL1
SM-G930R6 1 country Android 8.0.0

Samsung Galaxy S7 G930R6WWS8CRL1 Firmware

Samsung Galaxy S7 G930R6WWS8CRL1 is an Android 8.0.0 firmware for United States (LRA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930R6WWS4CRI1: bootloader binary raised from 4 to 8, so after installing it there is no way back to older builds. A newer build for SM-G930R6 is available: G930R6WWSBCTA1.

Download firmware
9.2/10 (463)4,470 times
Android 8.0.0
OS Version
2018-12-06
Build Date
1
Countries
1
CSC codes
8
Bootloader binary

Bootloader binary 8. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary B (11) (latest: G930R6WWSBCTA1). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930R6WWS8CRL1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G930R6
    LRA United States
    		G930R68CRL1 — — Download

    No matching downloads

    How to flash G930R6WWS8CRL1

    • G930R6WWS8CRL1 has bootloader binary 8. Your device must run binary 8 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight152 g

    Specifications of SM-G930F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G930R6WWS8CRL1 is Android 8.0.0 firmware for Samsung Galaxy S7, released for United States (LRA). Samsung built it on 2018-12-06.

    No. A newer build for SM-G930R6 is available: G930R6WWSBCTA1. Install it instead of G930R6WWS8CRL1 unless you need this exact version. The previous build was G930R6WWS4CRI1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S7 must be on bootloader binary 8 or lower.

    This build uses bootloader binary 8. It can be flashed on a Samsung Galaxy S7 running binary 8 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 8.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.
    Model firmware by region