SM-G930U 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy S7 G930UUEU4API3 Firmware

Name: Samsung Galaxy S7 (SM-G930U)
Brand: Samsung
Availability: InStock

Samsung Galaxy S7 G930UUEU4API3 is an Android 6.0.1 (Marshmallow) firmware for United States (ACG, BST, LRA, SPR, TFN, TMB, TMK, USC, VMU, VZW, XAA, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930UUEU2APG9: Android updated from Android 6.0.1 (Nougat) to Android 6.0.1 (Marshmallow); bootloader binary raised from 2 to 4, so after installing it there is no way back to older builds. A newer build for SM-G930U is available: G930UUESBCTA3.

9.3/10 (452)51,918 times

Android 6.0.1 (Marshmallow)

OS Version

2016-09-09

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary B (11) (latest: G930UUESBCTA3). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G930UUEU4API3

Model	Region	CSC Version	Release date	Size	File name	Download
SM-G930U	ACG, BST, LRA, SPR, TFN, TMB, TMK, USC, VMU, VZW, XAA, XAS United States	G930UOYM4API3	2016-10-13	2.335 GiB	SM-G930U_1_20180414190314_fsbl8y4rw8_fac.zip MD5:73239a54cec1f4d8f0dce4a5c3667f99 SHA1:a6834aefef38acd65d1f82e1a276434cc9222f68

Device specifications

Launched withAndroid 6.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM4 GB
RAM typeLPDDR4
Rear camera resolution12 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight152 g

Specifications of SM-G930F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G930UUEU4API3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G930UUEU4API3 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G930UUEU4API3 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy S7, released for United States (ACG, BST, LRA, SPR, TFN, TMB, TMK, USC, VMU, VZW, XAA, XAS). Samsung built it on 2016-09-09.

No. A newer build for SM-G930U is available: G930UUESBCTA3. Install it instead of G930UUEU4API3 unless you need this exact version. The previous build was G930UUEU2APG9.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.335 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary 4 or lower.

This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy S7 running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 15 other builds of this model use the same binary, so you can switch between them in both directions.