Samsung Galaxy S7 G930VCCTS4BRC3
SM-G930VC 1 country Android 7.0 (Oreo)

Samsung Galaxy S7 G930VCCTS4BRC3 Firmware

Samsung Galaxy S7 G930VCCTS4BRC3 is an Android 7.0 (Oreo) firmware for United States (CCT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930VCCTU4BQK3: Android updated from Android 7.0 (Nougat) to Android 7.0 (Oreo). A newer build for SM-G930VC is available: G930VCCTSBCTA1.

Download firmware
9.4/10 (453)8,579 times
Android 7.0 (Oreo)
OS Version
2018-03-19
Build Date
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary B (11) (latest: G930VCCTSBCTA1). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930VCCTS4BRC3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G930VC
    CCT United States
    		G930VC4BRC3 — — — Download
    SM-G930VC
    CCT United States
    		G930VCCCT4BRC3 2018-04-09 2.609 GiB
    SM-G930VC_1_20200121144554_bd4m2n9934_fac.zip
    		Download

    No matching downloads

    How to flash G930VCCTS4BRC3

    • G930VCCTS4BRC3 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight152 g

    Specifications of SM-G930F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G930VCCTS4BRC3 is Android 7.0 (Oreo) firmware for Samsung Galaxy S7, released for United States (CCT). Samsung built it on 2018-03-19.

    No. A newer build for SM-G930VC is available: G930VCCTSBCTA1. Install it instead of G930VCCTS4BRC3 unless you need this exact version. The previous build was G930VCCTU4BQK3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.609 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy S7 running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.
    Model firmware by region