Samsung Galaxy Ace 2 I8160XXMB1
GT-I8160 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy Ace 2 I8160XXMB1 Firmware

Samsung Galaxy Ace 2 I8160XXMB1 is an Android 2.3.6 (Gingerbread) firmware for Germany (EPL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I8160XXLL2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I8160 is available: I8160ZSLK2.

Download firmware
8.7/10 (461)4,457 times
Android 2.3.6 (Gingerbread)
OS Version
1
Countries
1
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Ace 2 use bootloader binary Z (35) (latest: I8160ZSLK2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I8160XXMB1
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I8160
    EPL Germany
    		I8160EPLMB1 — — Download

    No matching downloads

    How to flash I8160XXMB1

    • I8160XXMB1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 2.3
    • Display diagonal9.65 cm (3.8")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency0.8 GHz
    • RAM0.75 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1500 mAh
    • Weight122 g

    Frequently Asked Questions

    I8160XXMB1 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Ace 2, released for Germany (EPL).

    No. A newer build for GT-I8160 is available: I8160ZSLK2. Install it instead of I8160XXMB1 unless you need this exact version. The previous build was I8160XXLL2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Ace 2 must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Ace 2 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 14 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Ace 2

    No changelog details available.
    Model firmware by region