Samsung Galaxy S Ⅲ mini I8190NZSAMJ1
GT-I8190N 2 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Ⅲ mini I8190NZSAMJ1 Firmware

Samsung Galaxy S Ⅲ mini I8190NZSAMJ1 is an Android 4.1.2 (Jelly Bean) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I8190NZCAMG2: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean); bootloader binary raised from C (12) to S (28), so after installing it there is no way back to older builds. A newer build for GT-I8190N is available: I8190NXXAOR1.

Download firmware
8.9/10 (477)11,071 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-11-12
Build Date
2
Countries
2
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Ⅲ mini use bootloader binary X (33) (latest: I8190NXXAOR1). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I8190NZSAMJ1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I8190N
    BRI Taiwan
    		I8190NOZSAMJ1 2013-11-12 2013-11-12 — —
    GT-I8190N
    TGY Hong Kong SAR China
    		I8190NOZSAMJ1 2013-11-12 2013-11-12 — —

    No matching downloads

    How to flash I8190NZSAMJ1

    • I8190NZSAMJ1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I8190NZSAMJ1 by region

    Samsung released this build in all regions (2) on the same day, November 12, 2013.

    Frequently Asked Questions

    I8190NZSAMJ1 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Ⅲ mini, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2013-11-12.

    No. A newer build for GT-I8190N is available: I8190NXXAOR1. Install it instead of I8190NZSAMJ1 unless you need this exact version. The previous build was I8190NZCAMG2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅲ mini must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy S Ⅲ mini running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary S (28).

    Other builds and changelog for Samsung Galaxy S Ⅲ mini

    No changelog details available.
    Model firmware by region