Samsung Galaxy FEEL I8580XXEAND2
GT-I8580 3 countries Android 4.2.2 (Jelly)

Samsung Galaxy FEEL I8580XXEAND2 Firmware

Samsung Galaxy FEEL I8580XXEAND2 is an Android 4.2.2 (Jelly) firmware for France (XEF), Italy (ITV), United Kingdom (BTU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for GT-I8580 is available: I8580ZNUAOG1.

9.0/10 (452)12,658 times
Android 4.2.2 (Jelly)
OS Version
n/a
Build Date
n/a
Security patch
3
Countries
3
CSC codes
E (14)
Bootloader binary

Bootloader binary E (14). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy FEEL use bootloader binary U (30) (latest: I8580ZNUAOG1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I8580XXEAND2
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I8580
    BTU United Kingdom
    		I8580OXAAND2 — —
    GT-I8580
    ITV Italy
    		I8580OXAAND2 — —
    GT-I8580
    XEF France
    		I8580OXAAND2 — —

    No matching downloads

    How to flash I8580XXEAND2

    • I8580XXEAND2 has bootloader binary E (14). Your device must run binary E (14) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.2
    • Display diagonal11.9 cm (4.7")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2000 mAh
    • Weight145 g

    Frequently Asked Questions

    I8580XXEAND2 is Android 4.2.2 (Jelly) firmware for Samsung Galaxy FEEL, released for France (XEF), Italy (ITV), United Kingdom (BTU).

    No. A newer build for GT-I8580 is available: I8580ZNUAOG1. Install it instead of I8580XXEAND2 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy FEEL must be on bootloader binary E (14) or lower.

    This build uses bootloader binary E (14). It can be flashed on a Samsung Galaxy FEEL running binary E (14) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary E (14).

    Other builds and changelog for Samsung Galaxy FEEL

    No changelog details available.
    Model firmware by region