GT-I9070P 3 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy S Advance (NFC) I9070PXXLPJ Firmware

Name: Samsung Galaxy S Advance (NFC) (GT-I9070P)
Brand: Samsung
Availability: InStock

Samsung Galaxy S Advance (NFC) I9070PXXLPJ is an Android 2.3.6 (Gingerbread) firmware for Hungary (TMH), NRJ, Poland (TPL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070PXXLPG_P2 https://samfirm.shop/build/I9070PXXLPG_P2: Android updated from Jelly(Android Bean) to Android 2.3.6 (Gingerbread); bootloader binary raised from P (25) to X (33), so after installing it there is no way back to older builds. This is the newest build for GT-I9070P.

8.8/10 (471)17,475 times

Android 2.3.6 (Gingerbread)

OS Version

2013-07-24

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: I9070PXXLPJ

Model	Region	CSC Version	Build Date	Release date	Size	File name
GT-I9070P	NRJ	I9070PNRJLP2	2013-07-24	2013-10-15	—	—
GT-I9070P	NRJ	I9070PNRJLP3	—	—	—	—
GT-I9070P	TMH Hungary	I9070PTMHLPJ	—	—	—	—
GT-I9070P	TPL Poland	I9070PTPLLPJ	2013-07-24	2013-10-07	—	—

How to flash I9070PXXLPJ

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9070PXXLPJ has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9070PXXLPJ is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy S Advance (NFC), released for Hungary (TMH), NRJ, Poland (TPL). Samsung built it on 2013-07-24.

Yes. I9070PXXLPJ is the newest build for GT-I9070P on SamFirm. The previous build was I9070PXXLPG_P2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Advance (NFC) must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Advance (NFC) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.