Samsung Galaxy S Advance (NFC) I9070PXXLPD
GT-I9070P 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy S Advance (NFC) I9070PXXLPD Firmware

Samsung Galaxy S Advance (NFC) I9070PXXLPD is an Android 2.3.6 (Gingerbread) firmware for Germany (DBT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070PXXLK5: Android updated from Jelly(Android Bean) to Android 2.3.6 (Gingerbread). A newer build for GT-I9070P is available: I9070PXXLPJ.

Download firmware
9.3/10 (480)4,413 times
Android 2.3.6 (Gingerbread)
OS Version
2013-04-10
Build Date
1
Countries
1
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I9070PXXLPD
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I9070P
    DBT Germany
    		I9070PDBTLPD 449.881 MiB
    GT-I9070P_DBT_1_20141129130810_2hwjofxp3r_fac.zip
    		Download

    No matching downloads

    How to flash I9070PXXLPD

    • I9070PXXLPD has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    I9070PXXLPD is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy S Advance (NFC), released for Germany (DBT). Samsung built it on 2013-04-10.

    No. A newer build for GT-I9070P is available: I9070PXXLPJ. Install it instead of I9070PXXLPD unless you need this exact version. The previous build was I9070PXXLK5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 449.881 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S Advance (NFC) must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Advance (NFC) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Advance (NFC)

    No changelog details available.
    Model firmware by region