Samsung Galaxy S Ⅱ Plus I9105XXAMD1
GT-I9105 2 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Ⅱ Plus I9105XXAMD1 Firmware

Samsung Galaxy S Ⅱ Plus I9105XXAMD1 is an Android 4.1.2 (Jelly Bean) firmware for Egypt (EGY), Saudi Arabia (WTL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9105XXAMC2: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean). A newer build for GT-I9105 is available: I9105XXANL2.

9.1/10 (474)8,797 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-04-15
First release
other regions until 2013-09-26
n/a
Security patch
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9105XXAMC1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9105
    EGY Egypt
    		I9105OJVAMD1 2013-09-26 2013-09-26 — —
    GT-I9105
    WTL Saudi Arabia
    		I9105OJVAMD1 2013-04-15 2013-09-24 — —

    No matching downloads

    How to flash I9105XXAMD1

    • I9105XXAMD1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9105XXAMD1 by region

    First release
    September 24, 2013
    Last region
    September 26, 2013
    Duration
    3 days
    Regions
    2
    1. Day 1 · · 1 region
      Saudi ArabiaWTL
    2. Day 3 · · 1 region
      EgyptEGY

    Device specifications

    • Launched withAndroid 4.1
    • Display diagonal10.9 cm (4.3")
    • Display resolution800 x 480 pixels
    • Display typeAMOLED
    • Processor frequency1.2 GHz
    • RAM1 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1650 mAh
    • Weight121 g

    Frequently Asked Questions

    I9105XXAMD1 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Ⅱ Plus, released for Egypt (EGY), Saudi Arabia (WTL). Samsung built it on 2013-04-15.

    No. A newer build for GT-I9105 is available: I9105XXANL2. Install it instead of I9105XXAMD1 unless you need this exact version. The previous build was I9105XXAMC2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅱ Plus must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Ⅱ Plus running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Ⅱ Plus

    No changelog details available.
    Model firmware by region