GT-I9200 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Mega 6.3 I9200UBUDOC1 Firmware

Name: Samsung Galaxy Mega 6.3 (GT-I9200)
Brand: Samsung
Availability: InStock

Samsung Galaxy Mega 6.3 I9200UBUDOC1 is an Android 4.4.2 (KitKat) firmware for Brazil (ZTO), Puerto Rico (PCT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9200XXUDNK1 https://samfirm.shop/build/I9200XXUDNK1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9200 is available: I9200UBUDOI1 https://samfirm.shop/build/I9200UBUDOI1.

8.8/10 (452)12,926 times

Android 4.4.2 (KitKat)

OS Version

2015-03-04

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: I9200UBUDOC1

Model	Region	CSC Version	Release date	Size	File name
GT-I9200	PCT Puerto Rico	I9200UWADOD1	2015-05-13	1.189 GiB	GT-I9200_1_20170412223226_dy4528ejcm_fac.zip
GT-I9200	ZTO Brazil	I9200DOD1	—	—	—
GT-I9200	ZTO Brazil	I9200ZTODOD1	2015-06-30	1.184 GiB	GT-I9200_1_20170215120200_b50sndydji_fac.zip

How to flash I9200UBUDOC1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9200UBUDOC1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9200UBUDOC1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Mega 6.3, released for Brazil (ZTO), Puerto Rico (PCT). Samsung built it on 2015-03-04.

No. A newer build for GT-I9200 is available: I9200UBUDOI1. Install it instead of I9200UBUDOC1 unless you need this exact version. The previous build was I9200XXUDNK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Mega 6.3 must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Mega 6.3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.