Samsung Galaxy Mega 6.3 I9200XXUDNF3
GT-I9200 6 countries Android 4.4.2 (KitKat)

Samsung Galaxy Mega 6.3 I9200XXUDNF3 Firmware

Samsung Galaxy Mega 6.3 I9200XXUDNF3 is an Android 4.4.2 (KitKat) firmware for 6 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9200XXUDNF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9200 is available: I9200UBUDOI1.

Download firmware
9.2/10 (479)26,479 times
Android 4.4.2 (KitKat)
OS Version
2014-06-24
Build Date
6
Countries
6
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9200XXUDNF3
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I9200
    EGY Egypt
    MID Iraq
    PAK Pakistan
    TUR Turkey
    		I9200OJVDNG1 1.135 GiB
    GT-I9200_1_20170224065000_9k1yhp5cnr_fac.zip
    		Download
    GT-I9200
    THL Thailand
    XXV Vietnam
    		I9200OLBDNF2 1.168 GiB
    GT-I9200_1_20170305090726_x6q7twvlxl_fac.zip
    		Download

    No matching downloads

    How to flash I9200XXUDNF3

    • I9200XXUDNF3 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    I9200XXUDNF3 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Mega 6.3, released for 6 countries, 6 CSC codes. Samsung built it on 2014-06-24.

    No. A newer build for GT-I9200 is available: I9200UBUDOI1. Install it instead of I9200XXUDNF3 unless you need this exact version. The previous build was I9200XXUDNF1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Mega 6.3 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Mega 6.3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Mega 6.3

    No changelog details available.
    Model firmware by region