GT-I9295 1 country Android 5.0.1 (Jelly)

Samsung Galaxy S 4 Active I9295VJUDOL1 Firmware

Name: Samsung Galaxy S 4 Active (GT-I9295)
Brand: Samsung
Availability: InStock

Samsung Galaxy S 4 Active I9295VJUDOL1 is an Android 5.0.1 (Jelly) firmware for Brazil (ZTO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9295VJUDOK1: Android updated from Android 4.4.2 (KitKat) to Android 5.0.1 (Jelly). A newer build for GT-I9295 is available: I9295XXUDRB1.

9.2/10 (451)4,415 times

Android 5.0.1 (Jelly)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: I9295VJUDOL1

Model	Region	CSC Version	Size	File name	Download
GT-I9295	ZTO Brazil	I9295ZTODOL1	—	—

Device specifications

Launched withAndroid 4.2.2
Display diagonal12.7 cm (5")
Display resolution1920 x 1080 pixels
Display typeTFT
Processor frequency1.9 GHz
Processor familyQualcomm Snapdragon
Processor model600
RAM2 GB
Rear camera resolution8 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity2600 mAh
Weight153 g

How to flash I9295VJUDOL1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9295VJUDOL1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9295VJUDOL1 is Android 5.0.1 (Jelly) firmware for Samsung Galaxy S 4 Active, released for Brazil (ZTO).

No. A newer build for GT-I9295 is available: I9295XXUDRB1. Install it instead of I9295VJUDOL1 unless you need this exact version. The previous build was I9295VJUDOK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S 4 Active must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 4 Active running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 60 other builds of this model use the same binary, so you can switch between them in both directions.