Samsung Galaxy S 4 Active I9295XXUDOG2
GT-I9295 1 country Android 5.0.1 (Lollipop)

Samsung Galaxy S 4 Active I9295XXUDOG2 Firmware

Samsung Galaxy S 4 Active I9295XXUDOG2 is an Android 5.0.1 (Lollipop) firmware for Germany (DTM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9295XXUDOF6, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9295 is available: I9295XXUDRB1.

Download firmware
9.2/10 (460)8,663 times
Android 5.0.1 (Lollipop)
OS Version
2015-07-09
Build Date
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I9295XXUDOG2
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I9295
    DTM Germany
    		I9295DOG2 — — Download
    GT-I9295
    DTM Germany
    		I9295DTMDOG2 1.395 GiB
    GT-I9295_1_20170322103739_ftg7f8pcwj_fac.zip
    		Download

    No matching downloads

    How to flash I9295XXUDOG2

    • I9295XXUDOG2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.2.2
    • Display diagonal12.7 cm (5")
    • Display resolution1920 x 1080 pixels
    • Display typeTFT
    • Processor frequency1.9 GHz
    • Processor familyQualcomm Snapdragon
    • Processor model600
    • RAM2 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight153 g

    Frequently Asked Questions

    I9295XXUDOG2 is Android 5.0.1 (Lollipop) firmware for Samsung Galaxy S 4 Active, released for Germany (DTM). Samsung built it on 2015-07-09.

    No. A newer build for GT-I9295 is available: I9295XXUDRB1. Install it instead of I9295XXUDOG2 unless you need this exact version. The previous build was I9295XXUDOF6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.395 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S 4 Active must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 4 Active running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 60 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 4 Active

    No changelog details available.
    Model firmware by region