Samsung Galaxy S Ⅲ I9300UBEMH5
GT-I9300 2 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Ⅲ I9300UBEMH5 Firmware

Samsung Galaxy S Ⅲ I9300UBEMH5 is an Android 4.1.2 (Jelly Bean) firmware for Brazil (ZTA, ZTM, ZTO), Ecuador (EBE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9300UBEMH3: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean). A newer build for GT-I9300 is available: I9300XXEMU8.

9.1/10 (474)17,277 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-08-27
First release
other regions until 2013-11-21
n/a
Security patch
2
Countries
4
CSC codes
B (11)
Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Ⅲ use bootloader binary X (33) (latest: I9300XXEMU8). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9300
    EBE Ecuador
    		I9300EBEEMH1I9300UBEMH1 2013-11-21 2013-11-21 — —
    GT-I9300
    ZTA Brazil
    		I9300UBEMH1I9300ZTAEMH2 2013-08-27 — — —
    GT-I9300
    ZTM Brazil
    		I9300UBEMH1I9300ZTMEMH1 2013-08-27 — — —
    GT-I9300
    ZTO Brazil
    		I9300UBEMI2I9300ZTOEMH1 2013-08-27 — — —

    No matching downloads

    How to flash I9300UBEMH5

    • I9300UBEMH5 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9300UBEMH5 by region

    Samsung released this build in all regions (1) on the same day, November 21, 2013.

    Device specifications

    • Launched withAndroid 4.0
    • Display diagonal12.2 cm (4.8")
    • Display resolution720 x 1280 pixels
    • Display typeAMOLED
    • Processor frequency1.4 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2100 mAh
    • Weight133 g

    Frequently Asked Questions

    I9300UBEMH5 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Ⅲ, released for Brazil (ZTA, ZTM, ZTO), Ecuador (EBE). Samsung built it on 2013-08-27.

    No. A newer build for GT-I9300 is available: I9300XXEMU8. Install it instead of I9300UBEMH5 unless you need this exact version. The previous build was I9300UBEMH3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅲ must be on bootloader binary B (11) or lower.

    This build uses bootloader binary B (11). It can be flashed on a Samsung Galaxy S Ⅲ running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 7 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Ⅲ

    No changelog details available.
    Model firmware by region