Samsung Galaxy S Ⅲ I9300XXEMD2
GT-I9300 2 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Ⅲ I9300XXEMD2 Firmware

Samsung Galaxy S Ⅲ I9300XXEMD2 is an Android 4.1.2 (Jelly Bean) firmware for Poland (PRT), United Kingdom (H3G). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9300XXEMC2: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean). A newer build for GT-I9300 is available: I9300XXEMU8.

Download firmware
9.4/10 (478)8,713 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-04-12
Build Date
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    GT-I9300
    H3G United Kingdom
    		I9300H3GEMD1I9300NELK2 2013-05-14 911.338 MiB
    GT-I9300_H3G_1_20140502183800_tsawohac67_fac.zip
    		Download
    GT-I9300
    PRT Poland
    		I9300PRTEMD1I9300XXEMC2 2013-06-13 1000.892 MiB
    GT-I9300_PRT_1_20140823111710_9hiay2rm00_fac.zip
    		Download

    No matching downloads

    How to flash I9300XXEMD2

    • I9300XXEMD2 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9300XXEMD2 by region

    First release
    May 14, 2013
    Last region
    June 13, 2013
    Duration
    31 days
    Regions
    2
    1. Day 1 · · 1 region
      United KingdomH3G
    2. Day 31 · · 1 region
      PolandPRT

    Device specifications

    • Launched withAndroid 4.0
    • Display diagonal12.2 cm (4.8")
    • Display resolution720 x 1280 pixels
    • Display typeAMOLED
    • Processor frequency1.4 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2100 mAh
    • Weight133 g

    Frequently Asked Questions

    I9300XXEMD2 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Ⅲ, released for Poland (PRT), United Kingdom (H3G). Samsung built it on 2013-04-12.

    No. A newer build for GT-I9300 is available: I9300XXEMU8. Install it instead of I9300XXEMD2 unless you need this exact version. The previous build was I9300XXEMC2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅲ must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Ⅲ running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Ⅲ

    No changelog details available.
    Model firmware by region