Samsung Galaxy S3 Neo+ I9301IXXUAOF1
GT-I9301I 4 countries Android 4.4.2

Samsung Galaxy S3 Neo+ I9301IXXUAOF1 Firmware

Samsung Galaxy S3 Neo+ I9301IXXUAOF1 is an Android 4.4.2 firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9301IXCUAOA1: Android updated from Android 4.4.2 (KitKat) to Android 4.4.2. A newer build for GT-I9301I is available: I9301IXCUARA1.

Download firmware
9.1/10 (459)16,961 times
Android 4.4.2
OS Version
2015-06-02
Build Date
4
Countries
4
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9301IXXUAOF1
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I9301I
    ETL Czechia
    		I9301IOXXAOF1 — — Download
    GT-I9301I
    LUX Luxembourg
    		I9301IAOF2 — — Download
    GT-I9301I
    SEE Serbia
    		I9301IOXXAOF1 — — Download
    GT-I9301I
    VVT Bulgaria
    		I9301IAOE1 — — Download

    No matching downloads

    How to flash I9301IXXUAOF1

    • I9301IXXUAOF1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    I9301IXXUAOF1 is Android 4.4.2 firmware for Samsung Galaxy S3 Neo+, released for 4 countries, 4 CSC codes. Samsung built it on 2015-06-02.

    No. A newer build for GT-I9301I is available: I9301IXCUARA1. Install it instead of I9301IXXUAOF1 unless you need this exact version. The previous build was I9301IXCUAOA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S3 Neo+ must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S3 Neo+ running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S3 Neo+

    No changelog details available.
    Model firmware by region