Samsung Galaxy S 3 LTE I9305XXBLL5
GT-I9305 2 countries

Samsung Galaxy S 3 LTE I9305XXBLL5 Firmware

Samsung Galaxy S 3 LTE I9305XXBLL5 is an Android firmware for Croatia (VIP), Germany (VIA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9305XXBLK5, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9305 is available: I9305XXBMR8.

Download firmware
8.7/10 (478)8,702 times
2012-12-26
Build Date
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    GT-I9305
    VIA Germany
    		I9305VIABLL3I9305AOBLL1 2013-01-11 1000.908 MiB
    GT-I9305_1_20170502203913_5xxctdw3lv_fac.zip
    		Download
    GT-I9305
    VIP Croatia
    		I9305VIPBLL3I9305XXBLL5 2013-01-15 975.98 MiB
    GT-I9305_1_20170502210313_b845ek7o96_fac.zip
    		Download

    No matching downloads

    How to flash I9305XXBLL5

    • I9305XXBLL5 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9305XXBLL5 by region

    First release
    January 11, 2013
    Last region
    January 15, 2013
    Duration
    5 days
    Regions
    2
    1. Day 1 · · 1 region
      GermanyVIA
    2. Day 5 · · 1 region
      CroatiaVIP

    Device specifications

    • Launched withAndroid 4.1.1
    • Display diagonal12.2 cm (4.8")
    • Display resolution1280 x 720 pixels
    • Display typeAMOLED
    • Processor frequency1.4 GHz
    • RAM2 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity2100 mAh
    • Weight131 g

    Frequently Asked Questions

    No. A newer build for GT-I9305 is available: I9305XXBMR8. Install it instead of I9305XXBLL5 unless you need this exact version. The previous build was I9305XXBLK5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S 3 LTE must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S 3 LTE running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 15 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 3 LTE

    No changelog details available.
    Model firmware by region