Samsung Galaxy S 4 (Exynos Octa) I9500UBUAMDE
GT-I9500 3 countries

Samsung Galaxy S 4 (Exynos Octa) I9500UBUAMDE Firmware

Samsung Galaxy S 4 (Exynos Octa) I9500UBUAMDE is an Android firmware for Argentina (ANC), Chile (CRC), Colombia (COL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9500ZNSJQB2: bootloader binary raised from S (28) to U (30), so after installing it there is no way back to older builds. A newer build for GT-I9500 is available: I9500ZCUJQD1.

Download firmware
9.4/10 (476)13,010 times
2013-04-12
Build Date
3
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9500UBUAMDE
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-I9500
    ANC Argentina
    		I9500ANCAMDE 2013-04-30 1.408 GiB
    GT-I9500_1_20160609120501_465l8v9ety_fac.zip
    		Download
    GT-I9500
    COL Colombia
    		I9500UWMAMDE 2013-04-30 1.507 GiB
    GT-I9500_1_20170131083713_askib3bt6g_fac.zip
    		Download
    GT-I9500
    CRC Chile
    		I9500UWAAMDE 2013-04-30 1.503 GiB
    GT-I9500_1_20170202172913_h6e4b12k05_fac.zip
    		Download

    No matching downloads

    How to flash I9500UBUAMDE

    • I9500UBUAMDE has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9500UBUAMDE by region

    Samsung released this build in all regions (3) on the same day, April 30, 2013.

    Device specifications

    • Launched withAndroid 4.2.2
    • Display diagonal12.7 cm (5")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight130 g

    Frequently Asked Questions

    No. A newer build for GT-I9500 is available: I9500ZCUJQD1. Install it instead of I9500UBUAMDE unless you need this exact version. The previous build was I9500ZNSJQB2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S 4 (Exynos Octa) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 4 (Exynos Octa) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 109 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 4 (Exynos Octa)

    No changelog details available.
    Model firmware by region