Samsung Galaxy S 4 (Snapdragon) I9505VJUHOC1
GT-I9505 3 countries Android 5.0.1 (KitKat)

Samsung Galaxy S 4 (Snapdragon) I9505VJUHOC1 Firmware

Samsung Galaxy S 4 (Snapdragon) I9505VJUHOC1 is an Android 5.0.1 (KitKat) firmware for Brazil (ZTA, ZTO), Chile (CHO), Panama (TPA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9505XXUHOB8: Android updated from Android 5.0.1 (Lollipop) to Android 5.0.1 (KitKat). A newer build for GT-I9505 is available: I9505XXUPQG1.

Download firmware
8.9/10 (459)17,234 times
Android 5.0.1 (KitKat)
OS Version
2015-03-10
Build Date
3
Countries
4
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9505VJUHOC1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-I9505
    CHO Chile
    TPA Panama
    		I9505UUBHOC1 2015-04-14 1.437 GiB
    GT-I9505_1_20170117095126_afp0twmff4_fac.zip
    		Download
    GT-I9505
    ZTA Brazil
    		I9505HOC1 — — — Download
    GT-I9505
    ZTO Brazil
    		I9505HOC1 — — — Download

    No matching downloads

    How to flash I9505VJUHOC1

    • I9505VJUHOC1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9505VJUHOC1 by region

    Samsung released this build in all regions (2) on the same day, April 14, 2015.

    Device specifications

    • Launched withAndroid 4.2.2
    • Display diagonal12.7 cm (5")
    • Display resolution1080 x 1920 pixels
    • Display typeAMOLED
    • Processor frequency1.9 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight130 g

    Frequently Asked Questions

    I9505VJUHOC1 is Android 5.0.1 (KitKat) firmware for Samsung Galaxy S 4 (Snapdragon), released for Brazil (ZTA, ZTO), Chile (CHO), Panama (TPA). Samsung built it on 2015-03-10.

    No. A newer build for GT-I9505 is available: I9505XXUPQG1. Install it instead of I9505VJUHOC1 unless you need this exact version. The previous build was I9505XXUHOB8.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.437 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S 4 (Snapdragon) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 4 (Snapdragon) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 101 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 4 (Snapdragon)

    No changelog details available.
    Model firmware by region