Samsung Galaxy S4 (LTE-A/S800) I9506XXUAMJ2
GT-I9506 3 countries

Samsung Galaxy S4 (LTE-A/S800) I9506XXUAMJ2 Firmware

Samsung Galaxy S4 (LTE-A/S800) I9506XXUAMJ2 is an Android firmware for France (FTM), Norway (TEN), United Kingdom (EVR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9506XXUAMI7, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9506 is available: I9506XXUDRB1.

Download firmware
9.0/10 (480)13,029 times
2013-10-10
Build Date
3
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9506XXUAMI1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9506
    EVR United Kingdom
    		I9506EVRAMI2 — — — — Download
    GT-I9506
    FTM France
    		I9506FTMAMI2 2013-10-10 2013-10-25 1.325 GiB
    GT-I9506_1_20170126144000_u851a36m3j_fac.zip
    		Download
    GT-I9506
    TEN Norway
    		I9506TENAMJ3 2013-10-10 2013-11-11 1.294 GiB
    GT-I9506_1_20170224144226_auhkkfdvb8_fac.zip
    		Download

    No matching downloads

    How to flash I9506XXUAMJ2

    • I9506XXUAMJ2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9506XXUAMJ2 by region

    First release
    October 25, 2013
    Last region
    November 11, 2013
    Duration
    18 days
    Regions
    2
    1. Day 1 · · 1 region
      FranceFTM
    2. Day 18 · · 1 region
      NorwayTEN

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight130 g

    Frequently Asked Questions

    No. A newer build for GT-I9506 is available: I9506XXUDRB1. Install it instead of I9506XXUAMJ2 unless you need this exact version. The previous build was I9506XXUAMI7.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S4 (LTE-A/S800) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S4 (LTE-A/S800) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 42 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S4 (LTE-A/S800)

    No changelog details available.
    Model firmware by region