Samsung Galaxy J1 J100HDDU0AOF1
SM-J100H 4 countries Android 4.4.4 (KitKat)

Samsung Galaxy J1 J100HDDU0AOF1 Firmware

Samsung Galaxy J1 J100HDDU0AOF1 is an Android 4.4.4 (KitKat) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J100HXCU0AOE3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J100H is available: J100HXXU0AQK1.

9.4/10 (454)17,273 times
Android 4.4.4 (KitKat)
OS Version
2015-06-08
Build Date
n/a
Security patch
4
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J100HDDU0AOF1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J100H
    BNG Bangladesh
    INS India
    NPL Nepal
    SLK Sri Lanka
    		J100HODD0AOF1 2015-06-23 565.254 MiB
    SM-J100H_1_20170313084252_t6aza4ihyd_fac.zip

    No matching downloads

    How to flash J100HDDU0AOF1

    • J100HDDU0AOF1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J100HDDU0AOF1 by region

    First release
    June 23, 2015
    Last region
    July 2, 2015
    Duration
    10 days
    Regions
    4
    1. Day 1 · · 1 region
      IndiaINS
    2. Day 10 · · 3 regions
      BangladeshBNGNepalNPLSri LankaSLK

    Device specifications

    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • RAM0.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1850 mAh
    • Weight122 g

    Frequently Asked Questions

    J100HDDU0AOF1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy J1, released for 4 countries, 4 CSC codes. Samsung built it on 2015-06-08.

    No. A newer build for SM-J100H is available: J100HXXU0AQK1. Install it instead of J100HDDU0AOF1 unless you need this exact version. The previous build was J100HXCU0AOE3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 565.254 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J1 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 94 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1

    No changelog details available.
    Model firmware by region