Samsung Galaxy J1 J100MLDXU0AOJ2
SM-J100ML 1 country Android 4.4.4 (KitKat)

Samsung Galaxy J1 J100MLDXU0AOJ2 Firmware

Samsung Galaxy J1 J100MLDXU0AOJ2 is an Android 4.4.4 (KitKat) firmware for Philippines (GLB, SMA, XTC, XTE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J100MLDXU0AOC1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J100ML is available: J100MLDXS0AQB1.

Download firmware
9.0/10 (460)17,325 times
Android 4.4.4 (KitKat)
OS Version
2015-10-05
Build Date
1
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J100MLDXU0AOJ2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J100ML
    GLB Philippines
    		J100MLOLC0AOI1 — — Download
    SM-J100ML
    SMA Philippines
    		J100MLOLC0AOI1 — — Download
    SM-J100ML
    XTC Philippines
    		J100MLOLC0AOI1 — — Download
    SM-J100ML
    XTE Philippines
    		J100MLOLC0AOI1 — — Download

    No matching downloads

    How to flash J100MLDXU0AOJ2

    • J100MLDXU0AOJ2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.4.4
    • Display diagonal10.9 cm (4.3")
    • Display resolution800 x 480 pixels
    • Display typeTFT
    • RAM0.768 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1850 mAh
    • Weight122 g

    Specifications of SM-J100MU, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J100MLDXU0AOJ2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy J1, released for Philippines (GLB, SMA, XTC, XTE). Samsung built it on 2015-10-05.

    No. A newer build for SM-J100ML is available: J100MLDXS0AQB1. Install it instead of J100MLDXU0AOJ2 unless you need this exact version. The previous build was J100MLDXU0AOC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1

    No changelog details available.
    Model firmware by region