Samsung GALAXY J1 J100VPPVRU4ARA2
SM-J100VPP 1 country

Samsung GALAXY J1 J100VPPVRU4ARA2 Firmware

Samsung GALAXY J1 J100VPPVRU4ARA2 is an Android firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J100VPPVRU4AQF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-J100VPP.

Download firmware
9.1/10 (29)4,505 times
2018-01-08
First release
other regions until 2018-01-12
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J100VPPVRU4ARA2
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J100VPP
    VZW United States
    		J100VPPVZW4ARA2 2018-01-12 2018-02-02 969.157 MiB
    SM-J100VPP_1_20180112010653_gj1m5usikf_fac.zip
    		Download
    SM-J100VPP
    VZW United States
    		J100VPP4ARA2 2018-01-08 — — — Download

    No matching downloads

    How to flash J100VPPVRU4ARA2

    • J100VPPVRU4ARA2 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM0.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1850 mAh
    • Weight122 g

    Specifications of SM-J100H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    Yes. J100VPPVRU4ARA2 is the newest build for SM-J100VPP on SamFirm. The previous build was J100VPPVRU4AQF1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 969.157 MiB; keep about twice that free on the computer to unzip it. The Samsung GALAXY J1 must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung GALAXY J1 running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY J1

    No changelog details available.
    Model firmware by region