Samsung Galaxy J1 Mini Prime J106BUBS0ARH2
SM-J106B 4 countries Android 6.0.1

Samsung Galaxy J1 Mini Prime J106BUBS0ARH2 Firmware

Samsung Galaxy J1 Mini Prime J106BUBS0ARH2 is an Android 6.0.1 firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J106BUBU0ARF6: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1. This is the newest build for SM-J106B.

Download firmware
9.1/10 (460)21,556 times
Android 6.0.1
OS Version
4
Countries
5
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J106BUBU0AQL1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J106B
    COO Colombia
    		J106BUUB0AQL1 — — Download
    SM-J106B
    EON Trinidad & Tobago
    		J106BUUB0AQL1 — — Download
    SM-J106B
    TPA Panama
    		J106BUUB0AQL1 — — Download
    SM-J106B
    TTT Trinidad & Tobago
    		J106BUUB0AQL1 — — Download
    SM-J106B
    UYO Uruguay
    		J106BUUB0AQL1 — — Download

    No matching downloads

    How to flash J106BUBS0ARH2

    • J106BUBS0ARH2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1500 mAh
    • Weight123 g

    Specifications of SM-J106, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J106BUBS0ARH2 is Android 6.0.1 firmware for Samsung Galaxy J1 Mini Prime, released for 4 countries, 5 CSC codes.

    Yes. J106BUBS0ARH2 is the newest build for SM-J106B on SamFirm. The previous build was J106BUBU0ARF6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 Mini Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Mini Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 31 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1 Mini Prime

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region