SM-J111F 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J1 Ace J111FXWU0ARC2 Firmware

Name: Samsung Galaxy J1 Ace (SM-J111F)
Brand: Samsung
Availability: InStock

Samsung Galaxy J1 Ace J111FXWU0ARC2 is an Android 5.1.1 (Lollipop) firmware for South Africa (XFA, XFE, XFV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J111FXWU0ARC1 https://samfirm.shop/build/J111FXWU0ARC1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J111F is available: J111FXWU0ARL2 https://samfirm.shop/build/J111FXWU0ARL2.

9.0/10 (472)13,178 times

Android 5.1.1 (Lollipop)

OS Version

2018-03-28

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Model	Region	CSC Version	MODEM/CP Version	Release date	Size	File name	Download
SM-J111F	XFA South Africa	J111FOJP0ARC2	J111FXWU0ARC1	2018-05-09	966.812 MiB	SM-J111F_10_20190213160740_odyy71qjjl_fac.zip
SM-J111F	XFE, XFV South Africa	J111FOJP0ARC2	J111FXXU0ARB1	2018-05-16	966.812 MiB	SM-J111F_10_20190213134753_hh3tyguhe2_fac.zip

Device specifications

Display diagonal10.9 cm (4.3")
Display resolution480 x 800 pixels
Display typeSAMOLED
Processor frequency1.5 GHz
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity1900 mAh
Weight131 g

How to flash J111FXWU0ARC2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J111FXWU0ARC2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J111FXWU0ARC2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J1 Ace, released for South Africa (XFA, XFE, XFV). Samsung built it on 2018-03-28.

No. A newer build for SM-J111F is available: J111FXWU0ARL2. Install it instead of J111FXWU0ARC2 unless you need this exact version. The previous build was J111FXWU0ARC1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 Ace must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Ace running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 44 other builds of this model use the same binary, so you can switch between them in both directions.