Samsung Galaxy J1 Ace J111FXWU0ARB3
SM-J111F 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J1 Ace J111FXWU0ARB3 Firmware

Samsung Galaxy J1 Ace J111FXWU0ARB3 is an Android 5.1.1 (Lollipop) firmware for South Africa (XFE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J111FXXU0ARB3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J111F is available: J111FXWU0ARL2.

Download firmware
8.9/10 (40)4,720 times
Android 5.1.1 (Lollipop)
OS Version
2018-02-21
First release
other regions until 2018-03-13
1
Countries
1
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-J111F
    XFE South Africa
    		J111FOJV0ARB3J111FXXU0ARB1 2018-03-13 2018-03-13 1007.716 MiB
    SM-J111F_1_20180313130555_k5jd1jkopf_fac.zip
    SM-J111F
    XFE South Africa
    		J111FOJV0ARB3J111FXWU0ARB3 2018-02-21 — — —

    No matching downloads

    How to flash J111FXWU0ARB3

    • J111FXWU0ARB3 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeSAMOLED
    • Processor frequency1.5 GHz
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1900 mAh
    • Weight131 g

    Frequently Asked Questions

    J111FXWU0ARB3 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J1 Ace, released for South Africa (XFE). Samsung built it on 2018-02-21.

    No. A newer build for SM-J111F is available: J111FXWU0ARL2. Install it instead of J111FXWU0ARB3 unless you need this exact version. The previous build was J111FXXU0ARB3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1007.716 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J1 Ace must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Ace running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 44 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1 Ace

    No changelog details available.
    Model firmware by region