Samsung Galaxy J1 J120WVLU2AQJ3
SM-J120W 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy J1 J120WVLU2AQJ3 Firmware

Samsung Galaxy J1 J120WVLU2AQJ3 is an Android 6.0.1 (Marshmallow) firmware for Canada (BMC, BWA, ESK, FMC, GLW, KDO, MTA, PCM, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J120WVLU2AQA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J120W is available: J120WVLS2AQL1.

Download firmware
9.1/10 (481)69,577 times
Android 6.0.1 (Marshmallow)
OS Version
2017-10-10
Build Date
1
Countries
16
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J120WVLU2AQJ3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J120W
    BMC, BWA, ESK, FMC, GLW, KDO, MTA, PCM, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC Canada
    		J120WOYA2AQJ3 2017-10-25 1.268 GiB
    SM-J120W_1_20171204104514_t7y6kcmnbp_fac.zip
    		Download

    No matching downloads

    How to flash J120WVLU2AQJ3

    • J120WVLU2AQJ3 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J120WVLU2AQJ3 by region

    First release
    October 25, 2017
    Last region
    October 30, 2017
    Duration
    6 days
    Regions
    16
    1. Day 1 · · 6 regions
      CanadaBMCBWAGLWPCMSOLVMC
    2. Day 6 · · 10 regions
      CanadaESKFMCKDOMTAPMBRWCSPCTLSVTRXAC

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeSAMOLED
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2050 mAh
    • Weight132 g

    Specifications of SM-J120WZ, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J120WVLU2AQJ3 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J1, released for Canada (BMC, BWA, ESK, FMC, GLW, KDO, MTA, PCM, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC). Samsung built it on 2017-10-10.

    No. A newer build for SM-J120W is available: J120WVLS2AQL1. Install it instead of J120WVLU2AQJ3 unless you need this exact version. The previous build was J120WVLU2AQA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.268 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J1 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J1 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1

    No changelog details available.
    Model firmware by region