Samsung Galaxy J2 J200GUDXU2APL1
SM-J200GU 6 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J2 J200GUDXU2APL1 Firmware

Samsung Galaxy J2 J200GUDXU2APL1 is an Android 5.1.1 (Lollipop) firmware for 6 countries, 9 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J200GUDXU1APJ1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-J200GU is available: J200GUDXU3AQL1.

Download firmware
9.4/10 (458)38,932 times
Android 5.1.1 (Lollipop)
OS Version
2016-12-07
Build Date
6
Countries
9
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J2 use bootloader binary 3 (latest: J200GUDXU3AQL1). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J200GUDXU2APL1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J200GU
    CAM Cambodia
    GLB, SMA, XTC, XTE Philippines
    MYM Myanmar (Burma)
    THL Thailand
    +2 more countries
    XME Malaysia
    XXV Vietnam
    		J200GUOLB2APL1 2016-12-28 1.027 GiB
    SM-J200GU_1_20180206094814_ttkc2p18tq_fac.zip
    MD5:fee4f9ec92768d21699c2774ae261479
    SHA1:5c351e644cfed58b4ab0bd648f204e4ac74554e9
    		Download

    No matching downloads

    How to flash J200GUDXU2APL1

    • J200GUDXU2APL1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J200GUDXU2APL1 by region

    Samsung released this build in all regions (9) on the same day, December 28, 2016.

    Device specifications

    • Display diagonal11.9 cm (4.7")
    • Display resolution540 x 960 pixels
    • Display typeSAMOLED
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-J200, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J200GUDXU2APL1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J2, released for 6 countries, 9 CSC codes. Samsung built it on 2016-12-07.

    No. A newer build for SM-J200GU is available: J200GUDXU3AQL1. Install it instead of J200GUDXU2APL1 unless you need this exact version. The previous build was J200GUDXU1APJ1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.027 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J2 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J2 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 2.

    Other builds and changelog for Samsung Galaxy J2

    No changelog details available.
    Model firmware by region