Samsung Galaxy Grand Prime Pro J250FXWU2ARC6
SM-J250F 1 country Android 7.1.1 (Nougat)

Samsung Galaxy Grand Prime Pro J250FXWU2ARC6 Firmware

Samsung Galaxy Grand Prime Pro J250FXWU2ARC6 is an Android 7.1.1 (Nougat) firmware for India (INS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J250FXXU1ARC1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-J250F is available: J250FXWU2ATL1.

Download firmware
9.4/10 (451)4,420 times
Android 7.1.1 (Nougat)
OS Version
2018-03-16
Build Date
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J250FXWU2ARC6
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J250F
    INS India
    		J250FODD2ARC7 — —

    No matching downloads

    How to flash J250FXWU2ARC6

    • J250FXWU2ARC6 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typeSAMOLED
    • Processor frequency1.4 GHz
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight153 g

    Frequently Asked Questions

    J250FXWU2ARC6 is Android 7.1.1 (Nougat) firmware for Samsung Galaxy Grand Prime Pro, released for India (INS). Samsung built it on 2018-03-16.

    No. A newer build for SM-J250F is available: J250FXWU2ATL1. Install it instead of J250FXWU2ARC6 unless you need this exact version. The previous build was J250FXXU1ARC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand Prime Pro must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Grand Prime Pro running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 52 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime Pro

    • The security of your device has been improved.

    · Security patch update
    No changelog details available.

    • The security of your device has been improved.

    · Security patch update
    Show 13 older builds

    · The security of your device has been improved.

    • Overall stability of functions improved.

    · The security of your device has been improved.

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    Model firmware by region