Samsung Galaxy J2 Pro J250MUBS5ARL3
SM-J250M 1 country Android 7.1.1 (Nougat)

Samsung Galaxy J2 Pro J250MUBS5ARL3 Firmware

Samsung Galaxy J2 Pro J250MUBS5ARL3 is an Android 7.1.1 (Nougat) firmware for Dominican Republic (CDR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J250MUBS5ARK1: security patch 2018-12-01 instead of 2018-11-01. A newer build for SM-J250M is available: J250MUBS5ATJG.

Download firmware
9.3/10 (458)4,293 times
Android 7.1.1 (Nougat)
OS Version
2018-12-18
Build Date
2018-12-01
Security patch
1
Countries
1
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J250MUBS5ARL3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J250M
    CDR Dominican Republic
    		J250MUWA5ARL3 2019-01-22 — — Download

    No matching downloads

    How to flash J250MUBS5ARL3

    • J250MUBS5ARL3 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J250MUBS5ARL3

    · The security of your device has been improved.

    Device specifications

    • Launched withAndroid 7.1.1
    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typeSAMOLED
    • Processor frequency1.4 GHz
    • Processor familyQualcomm Snapdragon
    • Processor model425
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2600 mAh
    • Weight153 g

    Frequently Asked Questions

    J250MUBS5ARL3 is Android 7.1.1 (Nougat) firmware for Samsung Galaxy J2 Pro, released for Dominican Republic (CDR). It includes the 2018-12-01 security patch. Samsung built it on 2018-12-18.

    No. A newer build for SM-J250M is available: J250MUBS5ATJG. Install it instead of J250MUBS5ARL3 unless you need this exact version. The previous build was J250MUBS5ARK1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 Pro must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy J2 Pro running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 64 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2 Pro

    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.

    · The security of your device has been improved.

    Model firmware by region