Samsung Galaxy J2 Core J260AUCSABUD1
SM-J260A 1 country Android 9

Samsung Galaxy J2 Core J260AUCSABUD1 Firmware

Samsung Galaxy J2 Core J260AUCSABUD1 is an Android 9 firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J260AUCSABUA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J260A is available: J260AUCSCBVA2.

Download firmware
9.0/10 (38)245 times
Android 9
OS Version
2021-04-15
Build Date
1
Countries
1
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J2 Core use bootloader binary C (12) (latest: J260AUCSCBVA2). If your device already runs binary C (12), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J260AUCSABUD1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J260A
    ATT United States
    		J260AATTABUD1 2.163 GiB
    SM-J260A_1_20210415190936_apuwj9k7r2_fac.zip
    		Download

    No matching downloads

    How to flash J260AUCSABUD1

    • J260AUCSABUD1 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 8.1
    • Display diagonal12.7 cm (5")
    • Display resolution960 x 540 pixels
    • Display typePLS
    • RAM1 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight154 g

    Specifications of SM-J260F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J260AUCSABUD1 is Android 9 firmware for Samsung Galaxy J2 Core, released for United States (ATT). Samsung built it on 2021-04-15.

    No. A newer build for SM-J260A is available: J260AUCSCBVA2. Install it instead of J260AUCSABUD1 unless you need this exact version. The previous build was J260AUCSABUA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.163 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J2 Core must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy J2 Core running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2 Core

    No changelog details available.
    Model firmware by region