SM-J320F 4 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J3(2016) J320FDDU0APC1 Firmware

Name: Samsung Galaxy J3(2016) (SM-J320F)
Brand: Samsung
Availability: InStock

Samsung Galaxy J3(2016) J320FDDU0APC1 is an Android 5.1.1 (Lollipop) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J320FXXU0APB8, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J320F is available: J320FXXU0ARL2.

9.0/10 (451)17,221 times

Android 5.1.1 (Lollipop)

OS Version

2016-02-29

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: J320FDDU0APC1

Model	Region	CSC Version	Size	File name
SM-J320F	BNG Bangladesh	J320FODD0APC1	—	—
SM-J320F	INS India	J320FODD0APC1	—	—
SM-J320F	NPL Nepal	J320FODD0APC2	—	—
SM-J320F	SLK Sri Lanka	J320FODD0APC2	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution1280 x 720 pixels
Display typeSAMOLED
Processor frequency1.5 GHz
RAM1.5 GB
RAM typeLPDDR3
Rear camera resolution8 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity2600 mAh
Weight138 g

How to flash J320FDDU0APC1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J320FDDU0APC1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J320FDDU0APC1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J3(2016), released for 4 countries, 4 CSC codes. Samsung built it on 2016-02-29.

No. A newer build for SM-J320F is available: J320FXXU0ARL2. Install it instead of J320FDDU0APC1 unless you need this exact version. The previous build was J320FXXU0APB8.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2016) must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J3(2016) running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 58 other builds of this model use the same binary, so you can switch between them in both directions.