SM-J320F 4 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J3(2016) J320FXXU0APG2 Firmware

Name: Samsung Galaxy J3(2016) (SM-J320F)
Brand: Samsung
Availability: InStock

Samsung Galaxy J3(2016) J320FXXU0APG2 is an Android 5.1.1 (Lollipop) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J320FXXU0APG1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J320F is available: J320FXXU0ARL2.

9.2/10 (23)17,434 times

Android 5.1.1 (Lollipop)

OS Version

2016-07-29

First release

other regions until 2016-09-19

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: J320FXXU0APG2

Model	Region	CSC Version	Build Date	Release date	Size	File name
SM-J320F	CAU Kazakhstan MDO Moldova SER Russia	J320FOXE0APH1, J320FOXE0APG2	2016-07-29	2016-08-26	999.019 MiB	SM-J320F_1_20171121130001_9av65a4u6k_fac.zip
SM-J320F	PRO Belgium	J320FPRO0APH2	2016-09-19	2016-09-20	917.834 MiB	SM-J320F_1_20160919203928_7w4s20boak_fac.zip
SM-J320F	PRO Belgium	J320F0APH2	2016-07-29	—	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution1280 x 720 pixels
Display typeSAMOLED
Processor frequency1.5 GHz
RAM1.5 GB
RAM typeLPDDR3
Rear camera resolution8 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity2600 mAh
Weight138 g

How to flash J320FXXU0APG2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J320FXXU0APG2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J320FXXU0APG2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J3(2016), released for 4 countries, 4 CSC codes. Samsung built it on 2016-07-29.

No. A newer build for SM-J320F is available: J320FXXU0ARL2. Install it instead of J320FXXU0APG2 unless you need this exact version. The previous build was J320FXXU0APG1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2016) must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J3(2016) running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 58 other builds of this model use the same binary, so you can switch between them in both directions.