SM-J320ZN 2 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J3(2016) J320ZNDOU1APF4 Firmware

Name: Samsung Galaxy J3(2016) (SM-J320ZN)
Brand: Samsung
Availability: InStock

Samsung Galaxy J3(2016) J320ZNDOU1APF4 is an Android 5.1.1 (Lollipop) firmware for Fiji (VFJ), Papua New Guinea (PNG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J320ZNDOU1APE1 https://samfirm.shop/build/J320ZNDOU1APE1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J320ZN is available: J320ZNDOU1ARA1 https://samfirm.shop/build/J320ZNDOU1ARA1.

8.8/10 (454)8,687 times

Android 5.1.1 (Lollipop)

OS Version

2016-06-28

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: J320ZNDOU1APF4

Model	Region	CSC Version	Size	File name	Download
SM-J320ZN	PNG Papua New Guinea	J320ZN1APF4	—	—
SM-J320ZN	VFJ Fiji	J320ZN1APG2	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution1280 x 720 pixels
Display typeSAMOLED
RAM1.5 GB
RAM typeLPDDR3
Rear camera resolution8 MP
Rear camera typeSingle camera
Battery capacity2600 mAh
Weight138 g

Specifications of SM-J320F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash J320ZNDOU1APF4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J320ZNDOU1APF4 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J320ZNDOU1APF4 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J3(2016), released for Fiji (VFJ), Papua New Guinea (PNG). Samsung built it on 2016-06-28.

No. A newer build for SM-J320ZN is available: J320ZNDOU1ARA1. Install it instead of J320ZNDOU1APF4 unless you need this exact version. The previous build was J320ZNDOU1APE1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2016) must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J3(2016) running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 14 other builds of this model use the same binary, so you can switch between them in both directions.