Samsung Galaxy J3(2016) J320ZNDOU1APH1
SM-J320ZN 2 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J3(2016) J320ZNDOU1APH1 Firmware

Samsung Galaxy J3(2016) J320ZNDOU1APH1 is an Android 5.1.1 (Lollipop) firmware for New Zealand (2DX, TNX, VNZ), VNX. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J320ZNDOU1APG2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J320ZN is available: J320ZNDOU1ARA1.

Download firmware
9.1/10 (454)35,111 times
Android 5.1.1 (Lollipop)
OS Version
2016-08-03
First release
other regions until 2016-09-21
2
Countries
4
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-J320ZN
    2DX New Zealand
    		J320ZN2DX1APH1J320ZNDOU1APG2 2016-09-21 2016-09-21 1006.734 MiB
    SM-J320ZN_1_20160921165128_2jnu7u2kvc_fac.zip
    SM-J320ZN
    2DX New Zealand
    		J320ZN1APH1J320ZNDOU1APH1 2016-08-03 — — —
    SM-J320ZN
    TNX New Zealand
    		J320ZNTNX1APH1J320ZNDOU1APG2 2016-09-21 2016-09-21 1021.553 MiB
    SM-J320ZN_1_20160921164228_049o41lday_fac.zip
    SM-J320ZN
    TNX New Zealand
    		J320ZN1APH1J320ZNDOU1APH1 2016-08-03 — — —
    SM-J320ZN
    VNX
    		J320ZNVNX1APH2J320ZNDOU1APG2 2016-09-21 2016-09-21 1018.358 MiB
    SM-J320ZN_1_20160921163227_csq40nvrml_fac.zip
    SM-J320ZN
    VNX
    		J320ZN1APH2J320ZNDOU1APH1 2016-08-03 — — —
    SM-J320ZN
    VNZ New Zealand
    		J320ZNVNZ1APH2J320ZNDOU1APG2 2016-09-21 2016-09-21 1018.356 MiB
    SM-J320ZN_1_20160921163601_z92t5lj1st_fac.zip
    SM-J320ZN
    VNZ New Zealand
    		J320ZN1APH2J320ZNDOU1APH1 2016-08-03 — — —

    No matching downloads

    How to flash J320ZNDOU1APH1

    • J320ZNDOU1APH1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J320ZNDOU1APH1 by region

    Samsung released this build in all regions (4) on the same day, September 21, 2016.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • RAM1.5 GB
    • RAM typeLPDDR3
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight138 g

    Specifications of SM-J320F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J320ZNDOU1APH1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J3(2016), released for New Zealand (2DX, TNX, VNZ), VNX. Samsung built it on 2016-08-03.

    No. A newer build for SM-J320ZN is available: J320ZNDOU1ARA1. Install it instead of J320ZNDOU1APH1 unless you need this exact version. The previous build was J320ZNDOU1APG2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2016) must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J3(2016) running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 14 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J3(2016)

    No changelog details available.
    Model firmware by region