Samsung Galaxy J3 J327R6WWS2BSC2
SM-J327R6 1 country Android 8.1.0 (Oreo)

Samsung Galaxy J3 J327R6WWS2BSC2 Firmware

Samsung Galaxy J3 J327R6WWS2BSC2 is an Android 8.1.0 (Oreo) firmware for United States (LRA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J327R6WWS1BRL1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-J327R6 is available: J327R6WWS2BTF2.

Download firmware
9.2/10 (477)8,674 times
Android 8.1.0 (Oreo)
OS Version
2019-03-19
First release
other regions until 2019-03-20
2019-03-01
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J327R6WWS2BSC2
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J327R6
    LRA United States
    		J327R6LRA2BSC2 2019-03-20 2019-04-09 1.9 GiB
    SM-J327R6_1_20200623164903_c6sgv85jin_fac.zip
    		Download
    SM-J327R6
    LRA United States
    		J327R62BSC2 2019-03-19 2019-04-09 — — Download

    No matching downloads

    How to flash J327R6WWS2BSC2

    • J327R6WWS2BSC2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J327R6WWS2BSC2

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeTFT
    • RAM1.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight148 g

    Specifications of SM-J327, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J327R6WWS2BSC2 is Android 8.1.0 (Oreo) firmware for Samsung Galaxy J3, released for United States (LRA). It includes the 2019-03-01 security patch. Samsung built it on 2019-03-19.

    No. A newer build for SM-J327R6 is available: J327R6WWS2BTF2. Install it instead of J327R6WWS2BSC2 unless you need this exact version. The previous build was J327R6WWS1BRL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.9 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J3 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J3 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J3

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region