SM-J330F 7 countries Android 8.0.0 (Oreo)

Samsung Galaxy J3(2017) J330FXXS3CTF1 Firmware

Name: Samsung Galaxy J3(2017) (SM-J330F)
Brand: Samsung
Availability: InStock

Samsung Galaxy J3(2017) J330FXXS3CTF1 is an Android 8.0.0 (Oreo) firmware for 7 countries, 7 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330FXWS3CTE2: Android updated from Android 9 (Pie) to Android 8.0.0 (Oreo). A newer build for SM-J330F is available: J330FXXU4CZC2.

9.2/10 (451)39,000 times

Android 8.0.0 (Oreo)

OS Version

2020-06-12

First release

other regions until 2020-07-28

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J3(2017) use bootloader binary 4 (latest: J330FXXU4CZC2). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name
SM-J330F	ETL Czechia EUR Greece ORX Slovakia ROM Romania +3 more countries SEB Baltic Europe SEE Serbia XEH Hungary	J330FOXX3CSK2	J330FXXS3CTE1	2020-07-28	2020-07-29	2.281 GiB	SM-J330F_1_20200724171804_5bn4iy6201_fac.zip
SM-J330F	ETL Czechia	J330FOXX3CSK2	J330FXXS3CTF1	2020-06-12	—	—	—
SM-J330F	XEH Hungary	J330FOXX3CSK2	J330FXXS3CTF1	2020-06-12	—	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution1280 x 720 pixels
Display typeTFT
Processor frequency1.4 GHz
RAM2 GB
Rear camera resolution13 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity2400 mAh
Weight142 g

How to flash J330FXXS3CTF1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J330FXXS3CTF1 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J330FXXS3CTF1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J3(2017), released for 7 countries, 7 CSC codes. Samsung built it on 2020-06-12.

No. A newer build for SM-J330F is available: J330FXXU4CZC2. Install it instead of J330FXXS3CTF1 unless you need this exact version. The previous build was J330FXWS3CTE2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.281 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J3(2017) must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J3(2017) running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 45 other builds of this model use the same binary, so you can switch between them in both directions.