Samsung Galaxy J3(2017) J330FXXU3CSI4
SM-J330F 2 countries Android 9

Samsung Galaxy J3(2017) J330FXXU3CSI4 Firmware

Samsung Galaxy J3(2017) J330FXXU3CSI4 is an Android 9 firmware for Poland (DPL, TPL), Spain (XEC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330FXXU3CSH1: Android updated from Android 9 (Pie) to Android 9. A newer build for SM-J330F is available: J330FXXU4CZC2.

Download firmware
9.1/10 (38)13,420 times
Android 9
OS Version
2019-09-23
First release
other regions until 2019-10-01
2
Countries
3
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J3(2017) use bootloader binary 4 (latest: J330FXXU4CZC2). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J330FXXU3CSI4
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J330F
    DPL, TPL Poland
    		J330FDPX3CSI4 2019-10-01 2019-11-01 2.293 GiB
    SM-J330F_1_20210424175136_gv7ceqr9y8_fac.zip
    		Download
    SM-J330F
    XEC Spain
    		J330FXEC3CSI4 2019-10-01 2019-11-01 2.267 GiB
    SM-J330F_1_20191001133215_w4c77ino8o_fac.zip
    		Download
    SM-J330F
    XEC Spain
    		J330F3CSI4 2019-09-23 — — — Download

    No matching downloads

    How to flash J330FXXU3CSI4

    • J330FXXU3CSI4 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J330FXXU3CSI4 by region

    Samsung released this build in all regions (3) on the same day, November 1, 2019.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeTFT
    • Processor frequency1.4 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2400 mAh
    • Weight142 g

    Frequently Asked Questions

    J330FXXU3CSI4 is Android 9 firmware for Samsung Galaxy J3(2017), released for Poland (DPL, TPL), Spain (XEC). Samsung built it on 2019-09-23.

    No. A newer build for SM-J330F is available: J330FXXU4CZC2. Install it instead of J330FXXU3CSI4 unless you need this exact version. The previous build was J330FXXU3CSH1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2017) must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J3(2017) running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 45 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J3(2017)

    No changelog details available.
    Model firmware by region